If all the lamps are seated properly but a lampĭoesn't work, FIRST swap the bad lamp out with a good lamp and see if the problem is the Once in a great while, the shipping process will actually cause a wire toĬome loose at the ends of the lamp. Tanning lamps are seated properly as well (to prevent having to go back inside in a few While you are inside the tanning bed, make sure all the other Turn off all power to the tanning bed, remove the acrylic and If the tanning bed is new, this usually means a lamp has vibrated loose in the Lamp ends dark after a few weeks, others do not, but the UV output of the lamps should be Lamps are not older than 2/3rds of their rated life. This is normal and will not affect the tanning of the lamp appreciably if the
(This can be tested with a volt meter) This is aĭangerous situation and should be corrected by a licensed electrician. Needing 20AMP service, but run on 14ga wire will show 120VAC with no load, but drop toĩ5VAC when the tanning bed is on. Wiring, ie: the gauge of the wire to the circuit is too small. If your incoming voltage is correct, the likely problem is insufficient
If you have a 120VAC tanning bed, the voltage should be at least 110VAC (preferablyġ15-125VAC). Then you will need a buck/boost transformer to boost the voltage to a proper level. If you have 208 to 211VAC power (usually ONLY in a business building) If you have a 230VAC tanningīed, make sure that the available voltage is at least 215VAC (preferabley 220 to 230VAC) If your tanning bed has a digital timer, make sure you have selected the proper minute The knob is not pressed so hard into the tanning bed that it is jammed against the body of Passed 5 minutes, then roll it back to the proper time if under 5 minutes. If your tanning bed has an analog timer (twist knob style) make sure you turn it If you are familiar with a volt meter and have one handy, make sure If it doesn't work, then the problem isn't the If the tanning bed is 120V powered, try moving a lamp or similar plug in device to the Make sure the bed is fully assembled and in the closed position and try again.
Sunquest tanning bed not turning on when relay is engaged manual#
The CLOSED position, so read your owners manual and see if you have these safety devices. Some tanning beds will not operate unless all the panels are in place and the bed is in Make sure all the connections from the bench to the canopy (and to the airĬooling bar if so equipped) are connected tightly. Has a power switch, make sure it is in the ON position, and try both positions just to be Sure you are turning the timer enough to start the system. Make sure the breaker is in the ON position. New tanning beds: Make sure it is plugged in. My tanning bed is hotter than it used to be. The top of the tanning bed won't stay up (or down) Half the tanning bed (bench or canopy) will not work. Two or three lamps in a row quit working. Lamps try but fail to start, or start slowly These answers deal with home tanning beds in general, but more This guide covers many of the most common issues with just about any tanning bed and should help the home tanning bed owner deal with most problems without having to call for service. Your new tanning bed is backed by the most comprensive warranty in the industry but even the best tanning bed needs maintenance or a spare part once in a blue moon.
Protective eyewear is required for indoor tanning and must be worn at all times by everyone in the room with a tanning bed in operation.SunMaster, Alpha Sun and Virtual Sun Tanning Beds The 24RSP brings the salon tan right into your home.ĭark tanning lamps, coupled with angled polished reflectors, maximize the tanning rays for a dark, rich tan.Īll ETS Home Tanning Beds are ETL tested and certified for your personal safety and peace of mind. The SunQuest® 24RSP home tanning bed delivers the same dynamic tanning power as the popular SunQuest 24RS, but offers the convenience of operating on a 120-volt household circuit.
0 kommentar(er)
